Camcraft-Cams



Some thoughts on choosing a proper cam: STOCK CARS

1- To many racers the best cam is the one in the car when they get the chassis sorted out and the driver finally gets the track figured out.

2- Short duration cams with wider lobe separations usually yield much flatter torque curves

3- Longer rod motors prefer a shorter duration cam with wider lobe separation

4- Longer duration cams require tighter lobe separation to have any power off the corner. (not usually a preferable combination in 2 bbl classes.)

5- Stock exhaust manifolds or a highly restricted exhaust usually respond well to shorter exhaust duration and wider lobe separation. Power increases are most evident at higher rpm where exhaust backpressure is greatest and reversion is most prevalent.

6- Most unported heads approach 85 or 95 % of peak flow at .400 to .450 lift and do not need or want a maximum valve lift over .540 to.555. Often a low cam lift with 1.65 or 1.7 ratio rockers is very helpful on the intake side as long as lift is kept to about .550. Exhaust is less critical with 1.5 or 1.55 being the most popular.

7- Dyno testing doesn’t test drivability or throttle response of the engine.

8- The important numbers on a dyno sheet are about a thousand RPM above and below peak torque and peak horsepower. Peak numbers are for bragging purposes and high peak numbers do not win races.

9- The benefit of high ratio rockers is faster valve movement and the added lift is frequently detrimental in unported heads. It often helps to utilize a lower cam lift with high ratio rockers.

10- Changing the valve lash is a good way to get an indication of which way to go for your next cam change. You won’t hurt anything by going too tight but too loose will let the valves slam shut, causing damage to valves and seats. .004 to .006 loose is usually OK.

11- Look at the Major Intensity numbers to get an idea as to how radical the profile is.( major intensity is the difference between the .020 duration and the .050 duration.) Lower numbers are more radical but anything less than 27 or 28 degrees may be very hard on the valve train. Our 26-degree SXTL profiles are a notable exception to this.

12- Glowing exhaust pipes may be an indication of over scavenging by the exhaust. A shorter exhaust duration. Smaller headers, or even a restrictor plate at the header may help. The problem is often mixture burning in the exhaust rather than in the cylinder. Many people think a lean mixture causes it. Be sure to ascertain which problem you have as the lean mixture is a much more serious problem and can cause quick meltdown.

Camshaft intensity is a measurement term coined by Harvey Crane to compare ramp characteristics of camshafts.

• Hydraulic Intensity is the difference between the .004 duration and the .050 duration.
• Minor intensity is the difference between the .010 duration and the .050 duration.
• Major intensity is the difference between the .020 duration and the .050 duration

Lower numbers indicate more radical profiles but too low can be too radical and lead to noisy valve train and even to broken parts.

 

Our Location

54 Atrium Trail
Arden, NC, 28704

For driving directions, click HERE

Phone (828) 681-5183
Toll Free (800) 426-2261
Fax (828) 681-5185

Email: charles@camcraftcams.com

 

Happy Customers

Charles,
Thanks for the great cam and kit.  With your 240/240 .410 lift lobes on a 110 center we made 365 rwhp in our 331" Nova with a 2-bbl carb, about 40 hp up from the Comp cam we ran last year.  The torque peak was at 4500 rpm and the power peak was at 6500 rpm, well suited for the long uphill road sections we use.  I had no problems at all with the engine, no valve lashing was necessary and we used one set of plugs for the entire race. We finished 2nd in our class behind a Corvette, and eighth overall in a field of 70+ cars.  We were complimented frequently on how fast the little Nova ran, finishing well ahead of several 366" 4-bbl cars.  If only we could corner with the Vettes....

Thanks again,
Mike
Fairfield, CA

...read more Testimonials HERE


© Copyright Camcraft Cams • 54 Atrium Trail, Arden, NC, 28704 • charles@camcraftcams.com
Toll Free (800) 426-2261• (828) 681-5183 • Fax (828) 681-5185